山東機箱機柜別買錯！深度高度選型公式，閉眼選不踩坑

　　Don't buy the wrong Shandong chassis cabinet! Depth and height selection formula, choose without stepping on the pit with your eyes closed

　　在山東，不管是企業機房、工地監控，還是商鋪弱電設備安裝，機箱機柜都是必不可少的配套設施。但很多用戶在選購山東機箱機柜時，很容易陷入“憑感覺選尺寸”的誤區，近期就遇到不少用戶，因為買錯了機柜深度，導致設備插頭被柜門直接壓彎，不僅損壞了插頭，還可能影響設備正常運行，后續返工更換既費時間又費錢。今天就結合實際案例，給大家科普山東機箱機柜的正確選型方法，尤其是深度和高度的選擇，記住兩個簡單公式，閉眼都能選對。

　　In Shandong, whether it is enterprise computer rooms, construction site monitoring, or the installation of weak current equipment in shops, chassis and cabinets are essential supporting facilities. However, many users easily fall into the misconception of "choosing size based on feeling" when choosing Shandong chassis cabinets. Recently, we have encountered many users who have purchased the wrong cabinet depth, resulting in the equipment plug being directly bent by the cabinet door. This not only damages the plug, but may also affect the normal operation of the equipment. Subsequent rework and replacement will be time-consuming and costly. Today, based on practical cases, we will explain to you the correct selection method for Shandong chassis cabinets, especially the selection of depth and height. Remember two simple formulas, you can choose the right one with your eyes closed.

　　先說說容易踩坑的機柜深度選型，這也是很多用戶出錯的重災區。就像這次遇到的案例，用戶沒算準尺寸，買回來的機柜深度太淺，設備安裝后，柜門一關就直接壓住了設備插頭，沒多久插頭就被壓得嚴重變形，無法正常使用。其實選機柜深度，根本不用瞎猜，記住一個核心公式就夠了：機柜的深度≥設備的深度+200mm。這里的200mm，就是專門留給設備插頭、線路的余量，相當于給插頭“留條命”，避免出現擠壓損壞的情況。

　　First, let's talk about the depth selection of cabinets that are most prone to pitfalls, which is also a major area where many users make mistakes. Just like the case encountered this time, the user did not accurately calculate the size and bought a cabinet with a shallow depth. After the equipment was installed, the cabinet door immediately pressed down on the device plug as soon as it was closed. Soon after, the plug was severely deformed and unable to be used normally. In fact, when choosing the depth of the cabinet, there is no need to guess blindly. Just remember one core formula: the depth of the cabinet is ≥ the depth of the equipment+200mm. Here, 200mm is specifically reserved for the equipment plug and circuit, which is equivalent to leaving a "life" for the plug to avoid compression damage.

　　舉個簡單易懂的例子，方便山東的用戶快速理解和套用。如果你的設備深度是600mm，按照公式計算，機柜深度就需要600mm+200mm=800mm，此時選擇800mm深度的機柜，設備安裝后，后面會留有充足的空間，插頭、線路既能正常連接，又不會被柜門擠壓，后續維護、整理線路也更方便。很多用戶圖省事，覺得“機柜深度和設備深度差不多就行”，卻忽略了插頭和線路的占用空間，終導致設備損壞，反而得不償失。

　　Give a simple and easy to understand example to facilitate users in Shandong to quickly understand and apply. If the depth of your device is 600mm, according to the formula, the depth of the cabinet needs to be 600mm+200mm=800mm. At this time, choosing a cabinet with a depth of 800mm will leave sufficient space behind after the equipment is installed. The plugs and wires can be connected normally without being squeezed by the cabinet door, making maintenance and wiring more convenient in the future. Many users try to save time and think that "the depth of the cabinet is about the same as the depth of the equipment", but ignore the space occupied by the plugs and wires, which ultimately leads to equipment damage and is not worth the loss.

　　解決了深度選型的問題，再來說說機柜高度的選擇，這也是影響設備安裝合理性的關鍵。和深度一樣，高度選擇也有簡單的計算方法，不用盲目追求“越高越好”，也不用怕買矮了不夠用。要明確機柜的總高度，再結合標準U數換算，就能精準算出可用空間。行業內有個固定標準，1U的高度約等于44.45mm，我們可以用機柜總高度除以44.45mm，去掉小數點后的數字，得到的就是機柜的實際可用U數。

　　After solving the problem of deep selection, let's talk about the selection of cabinet height, which is also the key factor affecting the rationality of equipment installation. Like depth, there is also a simple calculation method for height selection. You don't have to blindly pursue "the higher the better", nor do you have to be afraid of buying short enough. Firstly, it is necessary to clarify the total height of the cabinet, and then combine it with the standard U-number conversion to accurately calculate the available space. There is a fixed standard in the industry that a height of 1U is approximately 44.45mm. We can divide the total height of the cabinet by 44.45mm and remove the decimal point to obtain the actual number of available U units in the cabinet.

　　比如常見的機柜總高度2100mm（也就是2.1米），用2100÷44.45≈47.24，去掉小數點后，這臺機柜的可用高度就是47U；而2000mm（2米）高的機柜，換算后約為44.99，實際可用高度就是42U。可能有用戶會問，42U的機柜能裝多少設備？其實完全不用愁，一般情況下，42U的機柜裝30個設備是綽綽有余的，剩余的空間還能留給線路整理、散熱，以及后續新增設備，空間分配非常合理，既不浪費，也不會不夠用。

　　For example, the total height of a common cabinet is 2100mm (2.1 meters), which is calculated as 2100 ÷ 44.45 ≈ 47.24. After removing the decimal point, the usable height of this cabinet is 47U. However, for a cabinet with a height of 2000mm (2 meters), the converted usable height is about 44.99, and the actual usable height is 42U. Some users may ask how many devices can be installed in a 42U cabinet? In fact, there is no need to worry at all. In general, a 42U cabinet is more than enough to accommodate 30 devices, and the remaining space can be reserved for line organization, heat dissipation, and subsequent equipment addition. The space allocation is very reasonable, neither wasting nor running out.

　　作為深耕山東機箱機柜行業的老代理商，見過太多用戶因為選型不當踩坑，要么深度不夠壓壞設備，要么高度過高浪費空間、增加成本，要么高度不夠無法安裝全部設備。其實山東機箱機柜的選型，核心就是“精準計算、留足余量”，深度和高度的兩個公式，看似簡單，卻能解決80%的選型難題，不管是新手還是有一定經驗的用戶，套用公式都能少走彎路。

　　As an old agent deeply involved in the Shandong chassis and cabinet industry, I have seen too many users fall into the trap due to improper selection. Either the depth is not enough to crush the equipment, the height is too high to waste space and increase costs, or the height is not enough to install all the equipment. In fact, the core of selecting computer cabinets in Shandong is "accurate calculation and sufficient margin". The two formulas for depth and height may seem simple, but they can solve 80% of the selection problems. Whether it is a novice or an experienced user, applying the formulas can avoid detours.

　　在這里也提醒山東的用戶，選購機箱機柜時，不要只看，更要注重尺寸適配，畢竟機柜是用來保護設備、規范線路的，尺寸選錯了，再好的質量也沒用。如果遇到不確定的地方，比如不知道設備深度怎么測量、總高度怎么換算，或者有特殊設備的安裝需求，不用自己瞎琢磨，及時咨詢代理商，就能獲得精準的選型建議，避免返工浪費。

　　Here, we also remind users in Shandong that when choosing chassis and cabinets, they should not only consider the price, but also pay attention to size adaptation. After all, cabinets are used to protect equipment and standardize circuits. Choosing the wrong size will result in poor quality. If you encounter uncertainty, such as not knowing how to measure the depth of the equipment, how to convert the total height, or having installation requirements for special equipment, you don't have to guess by yourself. Consult professional agents in a timely manner to obtain accurate selection suggestions and avoid rework and waste.

　　總的來說，山東機箱機柜的選購沒有想象中復雜，只要記住深度和高度的選型公式，結合自己的設備實際情況，精準計算、留足余量，就能閉眼選對，既保護設備，又能合理利用空間、控制成本。希望這篇科普能幫到正在選購山東機箱機柜的用戶，避開選型誤區，買到適配又實用的產品，讓設備運行更穩定、維護更省心。

　　Overall, the selection of chassis cabinets in Shandong is not as complicated as imagined. As long as you remember the selection formulas for depth and height, combine them with your actual equipment situation, accurately calculate and leave enough margin, you can choose the right one with your eyes closed. This not only protects equipment safety, but also makes reasonable use of space and controls costs. I hope this science popularization can help users who are currently choosing Shandong chassis cabinets to avoid selection errors and buy suitable and practical products, making equipment operation more stable and maintenance more worry free.